Toll Free: 1-888-878-0686

Mechanical Directional Controls

2 Way 2 Position Manual Valves

Typical application for MCA, MCB, MCF, MCL, and MCS is an emergency lowering device. Typical application for the MCI is a selector circuit when load holding is required in both directions. Typical application for the M2G is adjustable speed control or full pass of fluid motor.Typical application for the MCP is a pilot dump valve.

product details

  • 4-76 LPM (1-20GPM) maximum oil flows
  • 103-241 Bar (1500-4000 PSI) Maximum oil
  • Various handle configurations
  • Industry common cavities
  • Hardened parts for long life

Download PDF


Product Image

3 Way 2 Position Manual Valves

Typical application for a M3A depends on the porting used. The M3A can be used in a clutch application with porting option #1, for a single acting cylinder control with porting option #2, and for a selector application with porting option #3.

product details

  • 45 LPM (12 GPM) maximum oil flows.
  • 207 Bar (3000 PSI) Maximum oil pressure.
  • Various handle configurations.
  • Industry common cavities.
  • Hardened parts for long life.

Download PDF


Product Image

Direct Acting Check Valves

Typical application for the CVA, CVB, CVC, CVR, and CVS is load holding in a lift, check, or dump circuit.

product details

  • 9.5-151 LPM (2.5-40 GPM) maximum oil flows.
  • 70-345 Bar (1000-5000 PSI) Maximum oil pressure.
  • Fully gided popoets.
  • Industry common cavities.
  • Hardened parts for long life/low leakage.

Download PDF


Product Image

Pilot to Close Check Valves

Typical application for the CPD is in a regenerative circuit such as a baler or refuse compactor. The valve allows flow from the rod end of the cylinder to regenerate with pump flow to increase cylinder speed.

product details

  • 38-76 LPM (10-20 GPM) maximum oil flows
  • Various pilot ratios available
  • 240 Bar (3500 PSI) Maximum oil pressure
  • Industry common cavities
  • Hardened parts for long life/low leakage

Download PDF


Product Image

Pilot to Open Check Valves

Typical application for the CPB and CPC is load holding.

product details

  • 23-38 LPM (6-10 GPM) maximum oil flows
  • 240 Bar (3500 PSI) Maximum oil pressure
  • Various pilot rations available
  • Industry common cavities
  • Hardened parts for long life/low leakage

Download PDF


Product Image

Pilot to Shift Valves

Typical application for a 3 way pilot to shift: PTS is used as a priority flow control valve and PTT is used as a selector valve.

product details

  • 154 LPM (40 GPM) maximum oil flows
  • 240 Bar (3500 PSI) Maximum oil pressure
  • Internal leakage 164 ml/min (10 cu in/min)
  • Industry common cavities
  • Hardened parts for long life/low leakage

Download PDF


Product Image

Rotary Valves

Typical application for the MRA is a emergency -pass flow in a closed loop system.

product details

  • 150 LPM (40 GPM) maximum oil flows
  • 207 Bar (3000 PSI) Maximum oil pressure
  • Internal leakage 246 ml/min (15 cu in/min)
  • Industry common cavities
  • Hardened parts for long life/low leakage

Download PDF


Product Image

Featured Case Study

Featured Case Study Falcon Equipment
As the power infrastructure ages, maintaining power lines is becoming more labor intensive and the need for increased productivity and higher levels of safety is ever increasing. BC Hydro required a control system that would be safe to operate in close proximity to high voltage power lines while they are still active... read more »